MARC details
| 000 -LEADER |
|---|
| fixed length control field |
02794nam a2200253 a 4500 |
| 001 - CONTROL NUMBER |
|---|
| control field |
vtls000040728 |
| 003 - CONTROL NUMBER IDENTIFIER |
|---|
| control field |
KUKTEM |
| 005 - DATE AND TIME OF LATEST TRANSACTION |
|---|
| control field |
20251114204412.0 |
| 008 - FIXED-LENGTH DATA ELEMENTS--GENERAL INFORMATION |
|---|
| fixed length control field |
090723t2008 my a f m 000 0 eng d |
| 020 ## - INTERNATIONAL STANDARD BOOK NUMBER |
|---|
| International Standard Book Number |
THE0006581(Local) |
| 039 #9 - LEVEL OF BIBLIOGRAPHIC CONTROL AND CODING DETAIL [OBSOLETE] |
|---|
| Level of rules in bibliographic description |
201905161026 |
| Level of effort used to assign nonsubject heading access points |
amirul |
| Level of effort used to assign subject headings |
201107132231 |
| Level of effort used to assign classification |
VLOAD |
| Level of effort used to assign subject headings |
200908141651 |
| Level of effort used to assign classification |
VLOAD |
| Level of effort used to assign subject headings |
200908141632 |
| Level of effort used to assign classification |
VLOAD |
| -- |
200907231104 |
| -- |
ida84 |
| 040 ## - CATALOGING SOURCE |
|---|
| Original cataloging agency |
UMP |
| 090 ## - LOCALLY ASSIGNED LC-TYPE CALL NUMBER (OCLC); LOCAL CALL NUMBER (RLIN) |
|---|
| Classification number (OCLC) (R) ; Classification number, CALL (RLIN) (NR) |
TJ1191 .K43 2008 rs Bc. |
| 100 0# - MAIN ENTRY--PERSONAL NAME |
|---|
| Personal name |
Mohd Khairul Anuar Mohd Idris |
| 245 10 - TITLE STATEMENT |
|---|
| Title |
Effects of machining characteristics on electric discharge machine using different electrode materials / |
| Statement of responsibility, etc. |
Mohd Khairul Anuar Mohd Idris |
| 246 3# - VARYING FORM OF TITLE |
|---|
| Title proper/short title |
Effects of machining characteristics on electric discharge machine using different electrode materials |
| Medium |
[electronic resource] |
| 260 ## - PUBLICATION, DISTRIBUTION, ETC. |
|---|
| Place of publication, distribution, etc. |
Kuantan, Pahang : |
| Name of publisher, distributor, etc. |
UMP, |
| Date of publication, distribution, etc. |
2008 |
| 300 ## - PHYSICAL DESCRIPTION |
|---|
| Extent |
53 p. : |
| Other physical details |
ill. (some col.) ; |
| Dimensions |
30 cm. + |
| Accompanying material |
1 computer disc |
| 502 ## - DISSERTATION NOTE |
|---|
| Dissertation note |
Project paper (Bachelor of Mechanical Engineering) -- Universiti Malaysia Pahang - 2008 |
| 520 3# - SUMMARY, ETC. |
|---|
| Summary, etc. |
Electric discharge machining (EDM) is a non-traditional machining processes that involved a transient spark discharges through the fluid due to the potential difference between the electrode and the work piece. The aim of this project is to determine the proper electrode material for machining tool steels work pieces using electrical discharge machining (EDM). Basically, improper choose of electrode material in EDM machine may result a few problems like the machine may cause of poor machining performance and it will decrease the accuracy of the products. This paper presents a fundamental study of characteristic of electrode discharge machine (EDM) that is electrode wear ratio (EWR) and material removal rate (MRR) by using different electrode materials in order to increase the understanding of EDM processes. To archive this project objective, an experiment will be doing properly. By following the method, some literature review is going to do first before preparing the experimental set-up. Then experiment will be runs and the data of the experiment are taken. This is to make sure the analysis can be done in order to find the best electrode material. There are three electrodes material should be compared that are copper, brass and aluminum. Regarding the literature review, the higher material removal rate in the EDM machine, the better is the machining performance while the lower electrodes wear ratio in the EDM machine is the better and accurate performance characteristic. Thus as the expected result for this experiment, the copper electrode material will be the best electrode among others electrode for EDM machining process. |
| 650 #0 - SUBJECT ADDED ENTRY--TOPICAL TERM |
|---|
| Topical term or geographic name entry element |
Electric metal-cutting |
| 650 #0 - SUBJECT ADDED ENTRY--TOPICAL TERM |
|---|
| Topical term or geographic name entry element |
Machining |