MARC details
| 000 -LEADER |
|---|
| fixed length control field |
02126nam a2200253 a 4500 |
| 001 - CONTROL NUMBER |
|---|
| control field |
vtls000065536 |
| 003 - CONTROL NUMBER IDENTIFIER |
|---|
| control field |
KUKTEM |
| 005 - DATE AND TIME OF LATEST TRANSACTION |
|---|
| control field |
20251114204522.0 |
| 008 - FIXED-LENGTH DATA ELEMENTS--GENERAL INFORMATION |
|---|
| fixed length control field |
121101t2012 my da f m 000 0 eng d |
| 020 ## - INTERNATIONAL STANDARD BOOK NUMBER |
|---|
| International Standard Book Number |
THE0007507(Local) |
| 039 #9 - LEVEL OF BIBLIOGRAPHIC CONTROL AND CODING DETAIL [OBSOLETE] |
|---|
| Level of rules in bibliographic description |
201905161442 |
| Level of effort used to assign nonsubject heading access points |
fawwaz |
| Level of effort used to assign subject headings |
201211080930 |
| Level of effort used to assign classification |
huda |
| -- |
201211011456 |
| -- |
huda |
| 040 ## - CATALOGING SOURCE |
|---|
| Original cataloging agency |
UMP |
| 090 ## - LOCALLY ASSIGNED LC-TYPE CALL NUMBER (OCLC); LOCAL CALL NUMBER (RLIN) |
|---|
| Classification number (OCLC) (R) ; Classification number, CALL (RLIN) (NR) |
TS156 .S93 2012 rs Bc. |
| 100 0# - MAIN ENTRY--PERSONAL NAME |
|---|
| Personal name |
Mohamad Syahmi Shahrom |
| 245 10 - TITLE STATEMENT |
|---|
| Title |
Taguchi method approach on effect of lubrication condition on surface roughness in milling operation / |
| Statement of responsibility, etc. |
Mohamad Syahmi Shahrom |
| 260 ## - PUBLICATION, DISTRIBUTION, ETC. |
|---|
| Place of publication, distribution, etc. |
Kuantan, Pahang : |
| Name of publisher, distributor, etc. |
UMP , |
| Date of publication, distribution, etc. |
2012 |
| 300 ## - PHYSICAL DESCRIPTION |
|---|
| Extent |
xiv, 77 p. : |
| Other physical details |
ill. (some col.); |
| Dimensions |
30 cm. + |
| Accompanying material |
1 CD-ROM |
| 502 ## - DISSERTATION NOTE |
|---|
| Dissertation note |
Project paper (Bachelor of Manufacturing Engineering) -- Universiti Malaysia Pahang - 2012 |
| 504 ## - BIBLIOGRAPHY, ETC. NOTE |
|---|
| Bibliography, etc. note |
Bibliography : p. 71-73 |
| 520 ## - SUMMARY, ETC. |
|---|
| Summary, etc. |
This thesis presents an investigation into the MQL (minimum Quantity Lubrication) and wet machining in milling processes of AISI 1060 Aluminum work material with the main objective is to determine the effect of lubrication conditions on the surface roughness. Two types of insert had been used in this research, which is different in geometry selection is radius 0.8mm and 1.2mm. Three other parameters were also considered in this study; feed rate, depth of cut and cutting speed. The levels each parameter had been selected is four levels. The ranges of feed rate 0.05mm/min, 0.15mm/min,0.20mm/min and 0.25mm/min depth of cut used were 0.2mm, 0.4mm, 0.6mm and 0.8mm whereby the cutting speed values were 600mm/min, 800mm/min, 1000mm/min and 1200mm/min. The surface roughness was evaluated using surface roughness tester Mitutoyo. Taguchi method was used to predict the surface roughness. Finally, the experimental results showed good agreement with the estimated results. It was found that, MQL produced better surface finish as compared to wet machining. The result can significantly reduce cost and environmental pollution. |
| 650 #0 - SUBJECT ADDED ENTRY--TOPICAL TERM |
|---|
| Topical term or geographic name entry element |
Taguchi methods (Quality control) |
| 650 #0 - SUBJECT ADDED ENTRY--TOPICAL TERM |
|---|
| Topical term or geographic name entry element |
Surface roughness |