MARC details
| 000 -LEADER |
|---|
| fixed length control field |
02965nmm a2200313 a 4500 |
| 001 - CONTROL NUMBER |
|---|
| control field |
vtls000098419 |
| 003 - CONTROL NUMBER IDENTIFIER |
|---|
| control field |
KUKTEM |
| 005 - DATE AND TIME OF LATEST TRANSACTION |
|---|
| control field |
20251117113330.0 |
| 008 - FIXED-LENGTH DATA ELEMENTS--GENERAL INFORMATION |
|---|
| fixed length control field |
161214t2016 my fq d 001 0 eng d |
| 020 ## - INTERNATIONAL STANDARD BOOK NUMBER |
|---|
| International Standard Book Number |
THE0005104(Local) |
| 039 #9 - LEVEL OF BIBLIOGRAPHIC CONTROL AND CODING DETAIL [OBSOLETE] |
|---|
| Level of rules in bibliographic description |
201905131504 |
| Level of effort used to assign nonsubject heading access points |
hanafiah |
| Level of effort used to assign subject headings |
201712261151 |
| Level of effort used to assign classification |
nazri |
| -- |
201612140937 |
| -- |
safura |
| 040 ## - CATALOGING SOURCE |
|---|
| Original cataloging agency |
UMP |
| 090 ## - LOCALLY ASSIGNED LC-TYPE CALL NUMBER (OCLC); LOCAL CALL NUMBER (RLIN) |
|---|
| Classification number (OCLC) (R) ; Classification number, CALL (RLIN) (NR) |
FKP .A459 2016 r Bc. |
| 090 ## - LOCALLY ASSIGNED LC-TYPE CALL NUMBER (OCLC); LOCAL CALL NUMBER (RLIN) |
|---|
| Classification number (OCLC) (R) ; Classification number, CALL (RLIN) (NR) |
CD 10434 |
| 100 0# - MAIN ENTRY--PERSONAL NAME |
|---|
| Personal name |
Ali Zulfakar Bin Khairudin |
| 245 10 - TITLE STATEMENT |
|---|
| Title |
Design and development of drill bit sharpening jig for bench grinder / |
| Statement of responsibility, etc. |
Ali Zulfakar Bin Khairudin |
| 260 ## - PUBLICATION, DISTRIBUTION, ETC. |
|---|
| Place of publication, distribution, etc. |
Kuantan, Pahang : |
| Name of publisher, distributor, etc. |
UMP, |
| Date of publication, distribution, etc. |
2016 |
| 300 ## - PHYSICAL DESCRIPTION |
|---|
| Extent |
1 computer disc : |
| Other physical details |
digital data ; |
| Dimensions |
12 cm. |
| 500 ## - GENERAL NOTE |
|---|
| General note |
Theses Gred A |
| 500 ## - GENERAL NOTE |
|---|
| General note |
Faculty of Manufacturing Engineering |
| 502 ## - DISSERTATION NOTE |
|---|
| Dissertation note |
Project Paper (Bachelor of Engineering in Manufacturing Engineering (Hons.)) -- Universiti Malaysia Pahang – 2016 |
| 520 3# - SUMMARY, ETC. |
|---|
| Summary, etc. |
This thesis deals with design and development of the drill bit sharpening jigs for bench grinder. The objective of this thesis is to design the drill bit sharpener jig that enhance the better outcome rather than manual sharpening operation. The thesis follows with the development of the drill bit sharpening jig that can be attached to the bench grinder . The structural three-dimensional solid modeling of drill bit sharpening jig was developed using the computer-aided drawing software which is CATIA V5R21. The strategy of validation of the model design was developed. The generative part structural analysis was then performed using simulation in CATIA V5R21 to detect the Von Mises distribution.The design and suitable material will be validated. The fabrication of the jig may undergoes in various machining process such as milling , turning , electrical discharge wirecut and grinding . The assembled part shall be tested on the bench grinder. Besides , several dull drill bits will be sharpen using the jig. These assessment results are significant to improve the component design at the early developing stage.Further analysis will be conducted by testing the drilling process on the workpiece.The resharpen drill bits and the new drill bits will results on the difference surface roughness.Thus, the surface roughness analysis is performed to distinguish hole surface roughness outcomes for both drill bits.The results shows the difference of surface roughness between both hole surface is small and insignificant.Thus, it means that the outcomes is relatively same.The jig can also significantly reduce the cost and time to market, and improve product reliability and customer confidence. |
| 538 ## - SYSTEM DETAILS NOTE |
|---|
| System details note |
Item in PDF format |
| 610 20 - SUBJECT ADDED ENTRY--CORPORATE NAME |
|---|
| Corporate name or jurisdiction name as entry element |
Faculty of Manufacturing Engineering |
| General subdivision |
Dissertations |
| 650 #0 - SUBJECT ADDED ENTRY--TOPICAL TERM |
|---|
| Topical term or geographic name entry element |
Universities and Colleges |
| General subdivision |
Dissertations |
| 650 #0 - SUBJECT ADDED ENTRY--TOPICAL TERM |
|---|
| Topical term or geographic name entry element |
Theses |
| 856 40 - ELECTRONIC LOCATION AND ACCESS |
|---|
| Uniform Resource Identifier |
<a href="http://ecollib.ump.edu.my/id/eprint/3962">http://ecollib.ump.edu.my/id/eprint/3962</a> |
| Public note |
Access in library only |