04258nam a22003737a 4500 0 0 lcc 0 1 REF 20000 20000 REF 2019-11-19 0 FKEE .F37 2019 r Thesis T000000419 2021-11-11 00:00:00 2019-11-19 THESIS 0 0 lcc 0 1 REF 20000 20000 REF 2019-11-19 0 CD 12379 T000000420 2022-01-10 00:00:00 2019-11-19 THESIS 91237 91243 MY-KuUP 20251125105432.0 a|||||r|||| 000 0 ta 191119t20192019my a|||| |m|| 000 0 eng d THE0008291(Local) UMP eng UMP rda FKEE .F37 2019 r Thesis Farah Adiba Azman, author. Camera geometry determination based on circular's shape for peg-in-hole task / Farah Adiba Azman Kuantan, Pahang : UMP, 2019 © 2019 xii, 86 pages : illustrations (some color) ; 30 cm. + 1 CD-ROM rdacontent text rdacontent text rdamedia unmediated rdamedia computer rdacarrier volume rdacarrier computer disc rda text file PDF Faculty of Electrical & Electronics Engineering Thesis (Master of Science) -- Universiti Malaysia Pahang – 2019 Includes bibliographical references A simple, inexpensive system and effective in performing required tasks is the most preferable in industry. The peg-in-hole task is widely used in manufacturing process by using vision system and sensors. However, it requires complex algorithm and high Degree of Freedom (DOF) mechanism with fine movement. Hence, it will increase the cost. Currently, a forklift-like robot controlled by an operator using wired controllers is used to pick up one by one of the copper wire spools arranged side by side on the shelf to be taken to the inspection area. The holder and puller attached to the robot is used to pick up the spool. It is difficult for the operator to ensure the stem is properly inserted into the hole (peg-in-hole problem) because of the structure of the robot. However, the holder design is not universal and not applicable to other companies. The spool can only be grasped and pulled out from the front side and cannot be grasped using robot arm and gripper. In this study, a vision system is developed to solve the peg-in-hole problem by enabling the robot to autonomously perform the insertion and pick up the spool without using any sensors except a low-cost camera. A low-cost camera is used to capture images of copper wire spool in real-time video. Inspired by how human perceive an object orientation based on its shape, a system is developed to determine camera orientation based on the spool image condition and yaw angle from the center of the camera (CFOV) to CHS. The performance of the proposed system is analyzed based on detection rate analysis. This project is developed by using MATLAB software. The analysis is done in controlled environment with 50-110 cm distance range of camera to the spool. In addition, the camera orientation is analyzed between -20º to 20º yaw angle range. In order to ensure the puller will not scratch the spool, a mathematical equation is derived to calculate the puller tolerance. By using this, the system can estimate the spool position based on the camera orientation and distance calculation. Application of this system is simple and costeffective. A Modified Circular Hough Transform (MCHT) method is proposed and tested with existing method which is Circular Hough Transform (CHT) method to eliminate false circles and outliers. The results of the analysis showed detection success rate of 96% compared to the CHT method. It shows the MCHT method is better than CHT method. The proposed system is able to calculate the distance and camera orientation based on spool image condition with low error rate. Hence, it solves the peg-in-hole problem without using Force/Torque sensor. In conclusion, a total of 7 analysis consist of image pre-processing, image segmentation, object classification, comparison between CHT and MCHT, illumination measurement, distance calculation and yaw angle analysis were experimentally tested including the comparison with the existing method. The proposed system was able to achieve all the objectives. Faculty of Electrical & Electronics Engineering Universities and colleges Disertations Theses lcc THESIS