000			05340ntm a2200373 i 4500
999			_c100212 _d100218
003			MY-KuUP
005			20251125110822.0
006			t||||fr|||| 000 0
007			ta
008			231122t20232023my a|||fr|||| 000 0 eng d
020			_aTHE0009795 (Local) _qHardback
040			_aUMP _beng _cUMP _erda
090			_aFTKPM .L53 2023 r Thesis
100	1		_aNorlida Binti Jamil, _eauthor.
245	1	0	_aIndirect monitoring of surface quality based on the integration of support vector machine and 3d I-kaz techniques in the machining process / _cNorlida Binti Jamil
264		1	_aKuantan, Pahang : _bUMP, _c2023
264		4	_c©2023
300			_axix, 213 pages : _billustrations (some color) ; _c30 cm. + _e1 CD-ROM
336			_2rdacontent _atext
336			_2rdacontent _atext
337			_2rdamedia _aunmediated
337			_2rdamedia _acomputer
338			_2rdacarrier _avolume
338			_2rdacarrier _acomputer disc
347			_2rda _atext file _bPDF
500			_aFaculty of Manufacturing & Mechatronics Engineering Technology
502			_aThesis (Doctor of Philosophy) -- Universiti Malaysia Pahang – 2023
504			_aIncludes bibliographical references
520	3		_aImproved machining process quality can contribute to sustainable manufacturing in terms of economic, environmental, and social sustainability. Reducing waste, increasing efficiency, and improving product quality can also help manufacturers to reduce costs and increase productivity rate. Machining is one of the common methods in industry and plays a central role in modern manufacturing. For many years, researchers have been studying monitoring methods to produce the best surface quality. The measurement involves three distinct techniques, which are categorised into quantitative and visualisation methods. Monitoring methods can be classified as either direct or indirect methods. The common method of measuring machining quality undergoes manufacturing bottlenecks, as it is constrained by human inspection and expensive equipment. A slow process leads to higher labour costs and a high risk of equipment damage to the workpiece. The present study aims to bridge this gap by leveraging the capabilities of 3D I-kaz and medium Gaussian SVM models to improve accuracy and classification rates for determining surface quality. The specific objectives are to analyse the impact of machining parameters on statistical analysis, classify acceleration signals for surface roughness identification using SVM, integrate SVM with 3D I-kaz to improve surface quality identification and validate its effectiveness through experiments. The quantification of signal processing for ductile iron, FCD450 material on cutting parameters: rotation speed with 1000–3026 rev/mm, feed rate of 120–720 mm/min, axial of 0.75–3.5 mm, and radial depth of cut (RDOC) is studied and validated through experiments under dry and minimum quantity lubrication (MQL) conditions. Surface roughness was measured to verify the acceleration signal, while Pearson’s correlation coefficient was used to evaluate the correlation strength between the acceleration signal and surface roughness. The calculated coefficient, r-value, was found to be 0.6543, which indicates a positive but nonlinear correlation between the acceleration signal and surface roughness. The kurtosis value measured from acceleration signals and surface roughness information was then used to classify the machining condition and identification of the surface quality. In the first experiment, the model displayed an accuracy of 84.87% and 84.57% in terms of F1 values. It was observed that by adjusting the hyperparameter, the model’s accuracy was augmented to 85.53% and its F1 score was enhanced to 84.93%. Additionally, the model was applied in the second experiment, resulting in an accuracy of 84.0%. Before the classification of machined surface condition, the condition is identified through the support vector machine (SVM) technique, and it was demonstrated that the condition could be demarcated into five different levels of surface quality. From the experimental test data, acceleration and average roughness (Ra)-based indicators are identified for correlation analysis. A relation is developed, which enables the prediction or identification of surface quality directly based on the selected based indicators (3D I-kaz coefficient) without having to inspect the milling process for surface roughness. It was demonstrated that the integration of the 3D I-kaz and SVM model resulted in an accuracy and F1 score of 96.0% and 96.3% respectively, suggesting that the quantification data is viable for surface quality identification. A monitoring experiment was conducted in this study to validate the identification of surface quality through the instantaneous surface roughness level obtained from the experiment. In conclusion, indirect monitoring of surface quality using vibration signals can quickly identify the surface quality using SVM and 3D I-kaz analyses, thus reducing the time and cost associated with manual inspection and allowing for its use in many other machining processes.
610	2	0	_aFaculty of Manufacturing & Mechatronics Engineering Technology _xDissertations
650		0	_aUniversities and colleges _xDissertations
650		0	_aTheses
942			_2lcc _cTHESIS