000			04587ntm a2200325 i 4500
999			_c100587 _d100593
003			MY-KuUP
005			20251125110844.0
006			a||||fr|||| 000 0
007			ta
008			240415s20232023my a|||fr|||| 000 0 may d
020			_aTHE0009826 (Local) _qHardback
040			_aUMPSA _beng _cUMP _erda
090			_aFTKMA .F34 2023 r Thesis
100	1		_aNur Faeeza Binti Abdul Halim, _eauthor.
245	1	0	_aParameter study on low temperature vacuum drying with induced nucleation boiling for dewatering stingless bees honey / _cNur Faeeza Binti Abdul Halim
264		1	_aKuantan, Pahang : _bUMPSA, _c2023
264		4	_c©2023
300			_axvi, 106 pages : _billustrations ; _c30 cm. + _e1 CD ROM
336			_2rdacontent _atext
337			_2rdamedia _aunmediated
338			_2rdacarrier _avolume
347			_2rda _atext file _bPDF
500			_aFaculty of Mechanical and Automotive Engineering Technology
502			_aThesis (Master of Science) -- Universiti Malaysia Pahang – 2023
504			_aIncludes bibliographical references
520	3		_aOne of the issues faced by stingless bees beekeepers is related to the storing of Stingless Bees Honey (SBH) at room temperature. This is because SBH contains high water content which may cause fermentation. Hence, the dewatering process is necessary to reduce the water content and prevent fermentation. The conventional methods that are used to lower the water content of honey are not efficient and have the potential to degrade the nutritious content of honey. Thus, the Low Temperature Vacuum Drying with Induced Nucleation Boiling (LTVD-NB) method has been developed to solve the problem of honey dewatering efficiency while maintaining honey quality. As LTVD-NB method involve with nucleate boiling, therefore surface roughness (SR) and dewatering temperature could affect the performance of dewatering honey. However, research on the effect of SR and dewatering temperature on nucleate boiling is limited. It is known that SR determines cavity and affects boiling heat transfer process, whereas temperature determines heat flux (q”). It is believed that boiling heat transfer process is directly related to bubble nucleate on heated surface. However, there is a limited amount of research available on the effect of SR and dewatering temperature towards the characteristics of bubble nucleation in honey. Thus, the objective of this study was to investigate the effects of temperature and SR of stainless steel heater pipes on dewatering rate, nucleate boiling heat transfer (NBHT), and bubble nucleate characteristic during dewatering of SBH. 200 g of SBH sample was heated for five minutes at three different temperatures, which were 40, 45, and 50 °C using stainless steel heater pipes with SR of 0.80, 3.39, 8.82, and 11.33 μm at the pressure of 5 kPa. A digital camera was used to capture and record the formation of bubble nucleate on the heater surface during the experiment. The formation of bubble characteristic has been observed and analysed base on the number of bubble nucleated and the bubble departure frequency. Each experimental setting was performed three times. It was found that SR and temperature significantly affected the dewatering rate of SBH. The highest dewatering rate of 0.42 %/min was obtained at the roughest surface of 11.33 μm and highest temperature of 50 °C. It was five times faster compared to dewatering rate at 0.80 μm SR of 40 °C, which was only 0.08 %/min. The highest dewatering rate was obtained at the highest SR due to more nucleation sites, thus increased the number of bubbles depart. By roughening the heater surface, the heat transfer coefficient (HTC) was enhanced as more cavity and nucleation site were present on the surface. The 11.33 μm surface produced 143 % higher HTC than the 0.80 μm. In addition, the highest dewatering rate was obtained at higher temperature as the heat dispersion and transfer were better at higher temperature compared with lower temperature. This is because as temperature increased q”, bubble frequency departure from heater surface and HTC also increased. The maximum HTC obtained was around 10.11 kW/m2K, corresponding to the highest temperature tested at 50 °C. Thus, higher SR and temperature resulted in higher dewatering rate, and this correlated with the increment of nucleation site, bubble frequency depart from heater surface, q”, and HTC.
610	2	0	_aFaculty of Mechanical and Automotive Engineering Technology _xDissertations
650		0	_aUniversities and colleges _xDissertations
942			_2lcc _cTHESIS