000			04646ntm a2200337 i 4500
003			MY-KuUP
005			20260729150137.0
006			t||||fr|||| 000 0
007			ta
008			260729t20262026my a|||fr|||| 000 0 eng d
020			_aTHE0009499 (Local) _qHardback
040			_aUMPSA _beng _cUMPSA _erda
090			_aFTKPM .H37 2026 r Thesis
100	0		_aMohd Haris Murshidi Mohd Mdzuki, _eauthor.
245	1	0	_aInfluence of different sub-core materials on inductance in annealed passive magnetic components / _cMohd Haris Murshidi Mohd Mdzuki
264		1	_aKuantan, Pahang : _bUMPSA, _c2026
264		4	_c© 2026
300			_axiv, 82 pages : _billustrations (some color) ; _c30 cm. + _e1 CD-COM
336			_2rdacontent _atext
337			_2rdamedia _aunmediated
338			_2rdacarrier _avolume
347			_2rda _atext file _bPDF
500			_aFaculty of Manufacturing and Mechatronic Engineering Technology
502			_aThesis (Master of Science) -- Universiti Malaysia Pahang – 2026
504			_aIncludes bibliographical references
520	3		_aPassive magnetic components are known for their excellent magnetic permeability, low coercivity, and also high saturation flux density, is the foundation of various medium- and high-frequency technologies. It can be found on transformers, motors, generators, and also magnetic sensors. Among these, Fe-ribbon core is known as a key material in the production of inductive components. The magnetic properties of Fe-ribbon core are influenced by the magnetic field annealing process. The induced anisotropies and the softening can alter performance outcomes significantly. In addition, the presence of adjacent materials sub-cores—during annealing may affect the final inductance value of the cores. Up to the present, the influence of neighbouring materials on the final inductance of an Fe-ribbon core has not been thoroughly investigated. Observations from past magnetic test data revealed a recurring issue: A significant drop in inductance at 10 kHz for bottommost cores tested after magnetic annealing process. This drop not only leads to higher rejection rates but also reduced the production yield. Despite its impact on product quality, no research has been conducted to find out the root cause of this low inductance values on bottommost core compared with other Fe-ribbon core on the same annealing needle. Therefore, this study aims to investigate the influence of various sub-core materials and configurations on the magnetic performance of annealed Fe-ribbon cores, with a main focus to improve the consistency in inductance values in mass-production environment. The objectives of this research are twofold: (1) To investigate the influence of sub-core materials on the inductance value of annealed Fe-ribbon core, and (2) to analyse the relationship between hysteresis loss and inductance values of annealed Fe-ribbon core. Fe-ribbon core composed of Fe-Cu-Nb-B-Si alloy was used as the substrate material, while mild steel (ST37), alloy steel (AISI4140), stainless steel (SUS304) and ceramic (Al2O3) was used as the sub-cores. Magnetic annealing process was carried out using a furnace with a high holding temperature. The magnetic properties and hysteresis loops of the annealed cores were measured using a dedicated electrical/magnetic tester, UNITESTER. The areas under the loop computed using coordinate extraction software, WebPlotDigitizer and Gauss’s area formula. The observed variations in inductance deviation of bottommost Fe-ribbon core among different sub-core materials indicate that the deviation is primarily governed by the selected sub-core. Mild steel, which, classified as a ferromagnetic, showed the lowest deviation (10 %), followed by stainless steel which is paramagnetic (25 %) and ceramic that belong to diamagnetic (48 %). The results also indicated that hysteresis loss of the Fe-ribbon cores exhibits a non-linear relationship with inductance value. In addition, incorporating a weight support structure reduced mechanical stress on the core, leading to an increase in overall inductance value from 47.1 μH to 52.3 μH and a reduction in inductance deviation of bottommost Fe-ribbon core from 12.8 % to 12.6 %. Overall, the combination of a high-permeability sub-core material and a low-stress mechanical configuration minimized hysteresis loss while enhancing magnetic consistency in production of mass Fe-ribbon core.
610	2	0	_aFaculty of Manufacturing and Mechatronic Engineering Technology _xDissertations
650		0	_aUniversities and colleges _xDissertations
650		0	_aThesis _xDissertations
942			_2lcc _cTHESIS
999			_c105345 _d105351