MARC View

000			03852nmm a2200313 a 4500
001			vtls000098387
003			KUKTEM
005			20251117113330.0
008			161213s2016 my fq d 001 0 eng d
020			_aTHE0005077(Local)
039		9	_a201905101552 _bhanafiah _c201712121423 _dfateeha _y201612131137 _zsaini
040			_aUMP
090			_aFKP .A936 2016 r Bc.
090			_aCD 10406
100	0		_aMuhammad Azdnan Amat
245	1	0	_aAnalysis of the influence of viscosity to the liquid film flow between two plates _h[electronic resource] / _cMuhammad Azdnan Amat
260			_aKuantan, Pahang : _bUMP, _c2016
300			_a1 computer disc : _bdigital data ; _c12 cm.
500			_aFaculty of Manufacturing Engineering
500			_aTheses Gred B
502			_aProject Paper (Bachelor of Engineering in Manufacturing Engineering (Hons.)) -- Universiti Malaysia Pahang – 2016
520	3		_aThis thesis deals with analysis of the influence viscosity to the liquid film flow between two plates. How the different viscosity of liquid film can lead to the time taken to full-filling the gap between the two plates? What is the filling pattern of the liquid film upon flowing through the gap? Thus, the objective of this thesis are to analyze the time taken for liquid to full filling the gap between two plates influenced by different liquid viscosity and visualize the flow pattern of the liquid flow upon flowing through the gap between two plates. The procedures to do this project state as following. The two plates of glasses are prepared and the length and width of both plates are measured. The gap between the two plates is set to 50 μm, approximately by using double sided-tap. Then the liquid with 1cSt is sucked by syringe. After that the liquid is injected into the gap. The time taken is recorded to filling up the gap. In addition, the video is taken during the process of liquid film advancement. The experiment is repeated for two more times to get the average time taken and liquid film behavior is observed during the filling up process. The procedure is repeated with 100 cSt, 800 cSt and 10000 cSt of liquid. From the results, it is observed that the analysis with helping of Video to JPEG converter Software and Photoshop Software yields more accurate data then. Ho just using only stopwatch and scaling ruler. The acquired results show the relationship between viscosity and filling time and distance travelled under 10 seconds. The liquid with 1 cSt which is the most lowest produced shortest time taken compared to 100 cSt, 800 cSt and 10000 cSt. While the most higher liquid viscosity that is 10000 cSt would had shortest distance travelled of flow advancement within 10 seconds. On top of that, the preliminary results in determining liquid volume used really important in order to optimize the utility of using liquid viscosity. For the experiments, 3 ml of volume of liquid is the optimum volume for the liquid viscosity to flow between two plates stress. The obtained results indicate that the flow pattern of each liquid viscosity can be different. However, the ideal flow pattern showed in this thesis. The results concluded that the viscosity and flow pattern are affects the flowing liquid between two plates. Therefore, viscosity played a vital role for study the liquid flow for underfill process. The results can also significantly reduce the cost and time to market, and improve product reliability and sustainability.
538			_aItem in PDF format
610	2	0	_aFaculty of Manufacturing Engineering _xDissertations
650		0	_aUniversities and Colleges _xDissertations
650		0	_aTheses
856	4	0	_uhttp://ecollib.ump.edu.my/id/eprint/3944 _zAccess in library only
999			_aVIRTUA40 _c6871 _d6877
999			_aVTLSSORT0080020004000900090110002450260030005000500150205200538061006500650185609992