000			03923ntm a2200361 i 4500
999			_c97938 _d97944
003			MY-KuUP
005			20251125110131.0
006			t||||fr|||| 00| 0
007			ta
008			221018s2022 my a|||frm||| 00| 0 eng d
020			_aTHE0009376(Local) _qhardback
040			_aUMP _beng _cUMP _erda
090			_aFTKMA .Z55 2022 r Thesis
100	0		_aMuhammad Zikri Japri _eauthor.
245	1	0	_aNoise and vibration analysis in the diesel engine based on biodiesel usage / _cMuhammad Zikri Japri
264		1	_aKuantan, Pahang : _bUMP, _c2022
264		4	_c© 2022
300			_axv, 140 pages : _billustrations (some color) ; _c30 cm. + _e1 CD ROM
336			_atext _2rdacontent
337			_aunmediated _2rdamedia
337			_acomputer _2rdamedia
338			_avolume _2rdacarrier
338			_acomputer disc _2rdacarrier
347			_atext file _bPDF _2rda
500			_aFaculty of Mechanical and Automotive Engineering Technology
502			_aThesis (Master of Science) -- Universiti Malaysia Pahang – 2022
504			_aIncludes bibliographical references
520	3		_aUtilization of biodiesel has become one of the major interests in substituting fossil fuel parallel to the implementation of green technology which emphasizes the products to be more environmental-friendly. Nevertheless, despite having various kinds of biodiesel, this does not ensure suitability since the usage could improve or aggravate the engine due to higher combustion effects that further influence the higher level of engine noise and vibration, albeit major modification on the engine is not required. Therefore, this study had been conducted by experimental analysis to investigate the relation of noise and vibration level with biodiesel as a substitution fuel in the single cylinder, direct-injection diesel engine produced from various biodiesel blends, engine speed and engine load. The Root Mean Square (RMS) velocity, Sound Intensity Mapping (SIM) together with Sound Power Level (SPL) analyses were used to indicate the effectiveness of biodiesel in the attenuation of the noise and vibration level generated by the diesel engine. D100, B5, B10 and B20 of Palm Oil Methyl Ester (POME) had been utilized to operate the engine by 1200 to 2160 RPM with the application of engine load varied from 0 to 28 Nm. The measurement of the vibration data was done using the uniaxial accelerometer, while for the noise emission data, a pair of ½ inch of microphones were used. In the vibration aspect, the usage of the B20 blend was found to be the lowest level in almost all conditions tested due to the higher cetane number and oxygen content while the B5 and B10 usage tend to increase the vibration level compared to D100. It also can be noticed that the increment of engine load significantly increases the vibration level while increasing the engine speed does not influence the vibration to be higher since an incomplete combustion occurred which led to a reduction in the rate of pressure rise, thus reducing the vibration level in higher engine speed. In the noise emission analysis, the competitiveness between B20 and D100 could be seen in the low engine speed, where the lowest noise level was obtained by B20 while in the high engine speed, the lowest was obtained by D100. On top of that, the highest location of noise source was recorded at the cylinder head, crank-link components, radiator, flywheel and dynamometer. As can be concluded, the usage of POME as a biodiesel could be owed to the lower vibration and partially reducing the noise generated by the engine. Also, the most significant parameter that could contribute to the decrement of the level was the blend ratio followed by the engine load and engine speed.
610	2	0	_aFaculty of Mechanical and Automotive Engineering Technology _xDissertations
650		0	_aUniversities and colleges _xDissertations
650		0	_aTheses
942			_2lcc _cTHESIS