000			03812ntm a2200361 i 4500
999			_c97952 _d97958
003			MY-KuUP
005			20251125110132.0
006			t||||fr|||| 00| 0
007			ta
008			221028s2022 my a|||frm||| 00| 0 eng d
020			_aTHE0009386(Local) _qhardback
040			_aUMP _beng _cUMP _erda
090			_aFTKPM .A36 2022 r Thesis
100	0		_aAinur Munira Rosli, _eauthor.
245	1	0	_aMicrocutting performance monitoring – investigation on tool failure criterion / _cAinur Munira Rosli
264		1	_aKuantan, Pahang : _bUMP, _c2022
264		4	_c© 2022
300			_axiii, 109 pages : _billustrations (some color) ; _c30 cm. + _e1 CD ROM
336			_atext _2rdacontent
337			_aunmediated _2rdamedia
337			_acomputer _2rdamedia
338			_avolume _2rdacarrier
338			_acomputer disc _2rdacarrier
347			_atext file _bPDF _2rda
500			_aFaculty of Manufacturing and Mechatronic Engineering Technology
502			_aThesis (Master of Science) -- Universiti Malaysia Pahang – 2022
504			_aIncludes bibliographical references
520	3		_aIn recent years, there is an increasing demand for miniaturized components from various industries, such as biomedical, aerospace, electronics, automotive, and military industries, due to their technology advancement. As the technology advanced, the trend shows the components had become smaller and lighter but still carry out the same or more improved function. One of the processes that can create intricate small components is the microcutting process, where it can create micro sized components or prototype with cost effective and high-quality end product. However, the specific micro machining machine itself is expensive to own rather than using the conventional end milling machine that was already owned to carry out a microcutting process. In order to make this happen, this research studies the tool wear behaviour during low-speed microcutting of aluminium alloy 6065 and AISI 1045 steel material, where a tungsten carbide (wc) tool of 1.0mm and four flute is utilized. This is because we recognize that one of the essential factors in microcutting process is the micro cutting tool itself. The tool failure or wear effects the cost, average surface roughness, functionality, and the quality of the finished product greatly. The research is conducted under different cutting condition with varying feed rate of 0.001mm/tooth to 0.005mm/tooth and cutting speed of 3.142m/min to 9.425m/min using side milling process where the side flank face wear progression of the tool is measured. Then, the average surface roughness and chip size data are collected using a 3D laser measurement microscope. Based on the results, there is a similar tool wear trend of the microcutting process with the conventional methods. The tool shows more rapid wear rate and reduced tool life during micro cutting of AISI 1045 steel as it has higher material hardness compared to aluminium alloy 6065 although the machining process is still achievable. The premature tool failure of low-speed microcutting process is often focused on the entrance of the workpiece. Other than that, it is found that there are some instances where the average surface roughness had decreased abruptly when it is reaching the fracture zone, which is caused by the geometrical effect from the worn edge of the tool. This could be applied in future design of the micro tool suitable for low-speed machining. It is also concluded that appropriate selection of machining conditions has the potential to reduce tool wear rate and encourage longer tool life.
610	2	0	_aFaculty of Manufacturing and Mechatronic Engineering Technology _xDissertations
650		0	_aUniversities and colleges _xDissertations
650		0	_aTheses
942			_2lcc _cTHESIS